michigan dot was redoing a road near me and they spilled a bucket of white paint across the road, gotta see that awful mess every day on the way to work now
I'd use; large tarp, print and cut out 2 lane wide stencil. If it needs to be supported, use small PVC piping, 3D printed joints and cord. Wait till least noticable, stretch tarp, people roll out a word each, Boom, everyone goes home.
I was thinking rosin paper roll template, shiping tape the edges to keep them sharp, the letters look to be about 3 feet tall. Very possible for a DIY.
See, the key may be to yes, tape over the road. Close one lane, paint till quick dry, close others with cones. Finish one lane at a time with no tread Marks, in under 1 hr.
I was wondering about a line of spray paints with solenoid operated nozzles. A little bit of control logic and you can print your message just like an inkjet printer.
Create cutouts with cardboard or posterboard before hand of all the letters at the right size. Tape them together, and fold it up. When ready, hit the road, lay it out, paint over the top using a roller, remove the cutout and place in plastic bag(s) so you don't fuck up your car. With practice, you could probably do something like seen in the video in about 2 minutes.
Yes this 👆🏼👆🏼👆🏼Underground Artist Warfare at its finest. I suggest between 0300 and 0400. Graveyard cops are napping and most people with jobs aren’t on the road yet.
Wouldn’t it be easier to spray paint it? That way you’re not dealing with a roller and paint that would no doubt make a mess in your truck (no way you do this with a sedan).
A little spray can, yes. But what about one of those pneumatic paint sprayer airbrush-like thingys (I think I have one in my garage somewhere)? You would need to bring an air compressor.
Came to say this. The brand Ego has an attachment to make their lawn mower battery a plug and play 120v source. Not to mention new trucks and even cars have 120v outlets.
This would make it more quieter and easier to transport.
One person could do this, but would be most effective with maybe 6. driver, front and rear spotters, two people to hold down stencil, one to paint.
It’s gotta be some kind of quick drying stuff notice there’s no tire marks from when it was wet. Unless the highway was closed down for several hours...This is some kind of sorcery.
For smaller-letters or the side of a building, yes, but not for something this size.
You can buy large rolls of 2mil plastic on amazon or hardware stores, which should help contain the mess and make it easier to load and unload. I'd recommend some disposable gloves as well.
On a more pragmatic note, one could setup something to dump paint underneath a pickup or SUV, as a means of turning the "Black Lives Matter" Mural into a "something splatter splatter" mural.
I thought political murals were allowed? Unless it's only leftists murals that are allowed, but in that case just put a tiny, feint half inch "BLM" in the middle of one of the 0's and it's perfectly legal, right?
Notice the high cement wall barriers on each side of the highway. This was most certainly done at night when traffic volume was low. But imagine if a car came along and there's no where to get out of the way. RESPECT>
If they were on foot those angled wall barriers are perfect cover at that spot. If traffic was low enough they'd have plenty of time between cars, and if the road was straight enough they'd have a few minutes warning on the next set of headlights.
Reduces noise, causes a harmonic balanced disruption (sound bouncing at angles to each of the walls and back) which muffles the noise. Similar to a noise suppressor on a rifle which makes it difficult to determine by audio where the shot came from. WWG1WGA
"And we'll just swing over in this direction and.... Oh will you look at that? It appears to say TRUMP 2020. Better circle it a few more times to make sure"
Before the BLM riots, before the NYC/DC mayors painted their bullshit on public roads, I would have said "No". Now, I'm all for it. You reap what you sow.
The local news channels here (Seattle market) would blur the fuck out of that text as not to expose the audience to something so utterly disturbing, in the news channels opinion, to see.
We need a bus or motor home with the inside gutted and automation to do this where you just slow down to a few miles and hour hit a button and drive off. Gone in 60 seconds.
Almost on par with the trump sticker on the bear's collar.
I bet it WAS Trump Bear.. he based
Yeah, no human would be dumb enough to try to put it there, that bear had to have done it itself!
Right?! And I saw the video, I swear he growled "This is MAGA county"... Fact.
How do we mark this one Solved?
Would be pretty great if one said 2024
Kek
Gets even better.. 30.days ago in south boston! https://www.boston.com/news/local-news/2020/08/23/someone-painted-trump-2020-on-the-streets-of-southie-and-people-are-riled-up-about-it
This time it was 6 locations in the suburbs. https://boston.cbslocal.com/2020/09/21/trump-2020-graffiti-route-44-carver-middleboro/
that part of mass, south of boston, is full of hard working people. cranberries, carpenters, and landscapers.
Cranberry?
Thems is a hard-workin berry.
What, are ya on ya period?
this has meme potential
The glass-slap is the 2020 Red Wave, if you will.
https://boston.cbslocal.com/2020/09/22/trump-2020-paint-route-44-carver-middleboro-massachusetts/
And they have now been painted over.
Its ok. They made the news. Now all pedes know.
All Marxist Massholes know, too! MA is MAGA Country, bitch!
Interesting they called it graffiti.
That triggered the left badly, didn't it? Poor miserable pathetic losers.
Or the person planting Biden Harris signs in the burn spots along the freeways in The PNW.
Source? That sounds extra spicy
Wow, I might actually get to see one of their signs here in WA then!
That looks like some professional DOT work there.
BREAKING NEWS: DOT ENDORSES TRUMP!
Elaine Chao: "I'll allow it."
Nah, too clean for DOT. that's a contractor
michigan dot was redoing a road near me and they spilled a bucket of white paint across the road, gotta see that awful mess every day on the way to work now
I'd use; large tarp, print and cut out 2 lane wide stencil. If it needs to be supported, use small PVC piping, 3D printed joints and cord. Wait till least noticable, stretch tarp, people roll out a word each, Boom, everyone goes home.
I was thinking rosin paper roll template, shiping tape the edges to keep them sharp, the letters look to be about 3 feet tall. Very possible for a DIY.
See, the key may be to yes, tape over the road. Close one lane, paint till quick dry, close others with cones. Finish one lane at a time with no tread Marks, in under 1 hr.
At low traffic with a professional looking crew early in the morning this is very doable.
Now I need to start working on my stenciling.
I was wondering about a line of spray paints with solenoid operated nozzles. A little bit of control logic and you can print your message just like an inkjet printer.
How many commies will get rekt reeing over this.
Its like fishing w/dynamite. In a barrel.
I concur.
how can this be done so nicely? I would do this at night, but it would look shitty and i don't want to do shitty work for President Trump
Create cutouts with cardboard or posterboard before hand of all the letters at the right size. Tape them together, and fold it up. When ready, hit the road, lay it out, paint over the top using a roller, remove the cutout and place in plastic bag(s) so you don't fuck up your car. With practice, you could probably do something like seen in the video in about 2 minutes.
this guy stencils
He has the tapes to prove it
The CrafsMan steady craftin'.
CrafsMan style is always in style
Yes this 👆🏼👆🏼👆🏼Underground Artist Warfare at its finest. I suggest between 0300 and 0400. Graveyard cops are napping and most people with jobs aren’t on the road yet.
Can confirm, often have to leave for work before 6 (and before 5 in summer) and even in the busiest parts of NJ it's a ghost town.
arduino board. Set speed. Nozzles. Program. Pressurized paint system that easily fits under car. Red button.
Basically turn your car into a big MAGA inkjet printer head, but with road paint.
You've got me.
Punch in the speed, set cruise control, hit go.
Read the speed off the ODB port, and just MAGA as fast as you want until the paint runs out!
Thinking the same. Most vehicle data can be pulled but as delta pointed out, it may have a sloppy result at higher speeds.
This is the new HWNDU.
the board would open the nozzle on and off depending on the speed of the car.
4 or 5 nozzles but the pressure feeding them would need to adjusted for the speed too.
Its just a series of on off, code wise, but nozzles ans pressure would have to be calculated.
The piping system would need to be pressurized so... it couldn't be just pvc and definitely not regular paint unless it had quality connectors.
It needs quick dry paint, a pump system, a board that can be dialed to speed,.. phone dying here. Spitballing but totally possible
Honestly thing any suggestions here could work. We'd have to test them all for results. No matter what, the message gets made right?
I'm honestly happy so many folks are interested in this.
Yup, I was thinking about that. The speed of the vehicle would have to slow and likely industrial nozzles and thickish paint for super clean lines.
If large enough it wouldn't matter (think 3 to 4 lanes of a highway but rhat would take more passes ans have to be precise)
With more nozzles and entire sign could be painted while waiting at a traffic light. That would take some experimenting with but all of this would.
Batman enters the chat
Wouldn’t it be easier to spray paint it? That way you’re not dealing with a roller and paint that would no doubt make a mess in your truck (no way you do this with a sedan).
Take forever. When was the last time you rattle canned anything? Shit will wear out your trigger fingers!
A little spray can, yes. But what about one of those pneumatic paint sprayer airbrush-like thingys (I think I have one in my garage somewhere)? You would need to bring an air compressor.
Professional airless electric sprayer. Did houses with one when I was young. Fast and heavy spray. Small generator will run it.
Came to say this. The brand Ego has an attachment to make their lawn mower battery a plug and play 120v source. Not to mention new trucks and even cars have 120v outlets.
This would make it more quieter and easier to transport.
One person could do this, but would be most effective with maybe 6. driver, front and rear spotters, two people to hold down stencil, one to paint.
*Also, leave cellphones at home.
It’s gotta be some kind of quick drying stuff notice there’s no tire marks from when it was wet. Unless the highway was closed down for several hours...This is some kind of sorcery.
All the new road paints dry damn quick.
Even faster with a portable heat gun (low setting).
I think you can see tire marks on it.
It would take some balls to make some Fugazi traffic cones and flares but its possible. Still how do you get the fast lane haha
You have to go back.
For smaller-letters or the side of a building, yes, but not for something this size.
You can buy large rolls of 2mil plastic on amazon or hardware stores, which should help contain the mess and make it easier to load and unload. I'd recommend some disposable gloves as well.
Agree!
We found the PEDE right here ☝️☝️
We're all PEDE's Fren!
On a more pragmatic note, one could setup something to dump paint underneath a pickup or SUV, as a means of turning the "Black Lives Matter" Mural into a "something splatter splatter" mural.
Many variations of how to deface that into something completely different have been offered on here. I can't remember any now ...
oh, ok. I'll do that right now....
you can buy sticker letters for asphalt
Obey all traffic signs!
KAG
Kek!
👍🏻 Where is this? Near Boston I’m assuming . 👏🏻👏🏻👏🏻
good call... it's Massachusetts
Even better. I love when this stuff comes up in blue states.
My home town but I can’t take credit.
Well if you find whoever did it, tell them thanks for us and shake their hand.
Don’t worry, FBI will have 15 agents on the case stat.
In related news: Leftist swamp dwellers pulled 15 agents away from kidnapping investigations and major cartel busts.
I thought political murals were allowed? Unless it's only leftists murals that are allowed, but in that case just put a tiny, feint half inch "BLM" in the middle of one of the 0's and it's perfectly legal, right?
Notice the high cement wall barriers on each side of the highway. This was most certainly done at night when traffic volume was low. But imagine if a car came along and there's no where to get out of the way. RESPECT>
Stop! You guys are givin me ideas!
You did it walking your dog!
.make sure to have a spotter both ways.
Middle of the night, low traffic, straight stretch of road, there's these things called headlights that can be seen from several miles away.
Throw orange beacons on a pickup and a few orange cones.
It's a quiet road at night with good cover and easy access. No cameras lining the road like every other highway in this cucked state.
If they were on foot those angled wall barriers are perfect cover at that spot. If traffic was low enough they'd have plenty of time between cars, and if the road was straight enough they'd have a few minutes warning on the next set of headlights.
Anyone have any idea why those walls are angled the way they are? It seems like the most expensive way to cover a particular linear distance that way.
Reduces noise, causes a harmonic balanced disruption (sound bouncing at angles to each of the walls and back) which muffles the noise. Similar to a noise suppressor on a rifle which makes it difficult to determine by audio where the shot came from. WWG1WGA
Thanks, pede. TD.win is the greatest- ask and someone in here will know. Amazing
We have the best vandals don’t we folks?!?!
I approve. Don't spend my tax money 'fixing' that either.
Classic
WBZ Providing some free advertising!
Nice
Noice!
Noice!
Noice!
MAGA
Translation: NOOICE!
Definitely done very well. Looks professional
That's what I thought. By day they paint lines on parking lots, by night they MAGA.
Fabulous! 🇺🇸❤️🇺🇸
If BLM can be put unto public property than anything can. That is the precedent.
Probably the helicopter pilot.
"And we'll just swing over in this direction and.... Oh will you look at that? It appears to say TRUMP 2020. Better circle it a few more times to make sure"
I want this on every highway across America. That's what I call infrastructure 🇺🇸
Before the BLM riots, before the NYC/DC mayors painted their bullshit on public roads, I would have said "No". Now, I'm all for it. You reap what you sow.
A bit of maths and some open source engineering and this could be all over our roadways...
LOL. Hey, BLM set the precedent of painting roads...
The local news channels here (Seattle market) would blur the fuck out of that text as not to expose the audience to something so utterly disturbing, in the news channels opinion, to see.
Locals would need double rations of Liberty Juice.
Now we need it on airport runways.
Two terms. Two genders. Two scoops. And... two free ads 😂🇺🇸
Need to do one where the letters are vertical that the driver reads.
That's beautiful work!
We need a bus or motor home with the inside gutted and automation to do this where you just slow down to a few miles and hour hit a button and drive off. Gone in 60 seconds.
Looks Like We Got Us A Convoy!
"Is this graffiti?"
No it a MUREL
BASED and speedypilled
TWICE!
Need some on the train tracks.
stop trying to kill all the pedes.
do it ON TOP of the trains LOL
if you write something in sugar water then the moss and stuff makes it appear days later.
And in Massachusetts!
what if you cut stensils into each tire then had something spraying paint on your tire inside your wheel well.
also on bottom of your shoes.
Oriented to survive normal tire wear. Great work Patriot!
its clearly a protest, cars run over the sign (/s)
Hey, doesn't paint on a road help to insure a longer lasting surface with reduction of the wear and cracking of asphalt??????????????? WWG1WGA
They’ll s rub it off, paint “BLACK LIVES MATTER” across it and officially name it “Martin Luther King Highway.”
You know you triggered some libs when they send out the "eyes in the sky"
Now that's a mural I don't mind looking at.🤣
This is grade a MAGA.